Keyboards, pedals and Stop Midi Encoders
MIPC-1A Keyboard/Stop Midi Encoder
With the growing interest in Virtual Pipe Organ projects and prospect of converting manuals, a pedal board and stop keys to MIDI Data, a circuit and card featuring a crystal controlled microprocessor has been developed that allows use the existing organ console wiring. The MIPC-1A features 64 inputs that requires no diodes or switch buss rewiring, simply connect a wire from each key or stop contact to the corresponding input on the MIPC-1A.
The MIPC-1A has been designed to make the installation as effortless and easy to understand. To further simplify the installation, there are no programming codes to write or install. Simple DIP Switch selection for Keyboard/Stop mode, Midi Channel and Four Analog (Swell Shoe) functions.
The MIPC-1A Input to Midi Controller is the best and easiest to install device for that Virtual Pipe Organ project.
Features
The MIPC-1A has been designed to make the installation as effortless and easy to understand. To further simplify the installation, there are no programming codes to write or install. Simple DIP Switch selection for Keyboard/Stop mode, Midi Channel and Four Analog (Swell Shoe) functions.
The MIPC-1A Input to Midi Controller is the best and easiest to install device for that Virtual Pipe Organ project.
Features
- No Configuration files or Programming required
- 64 Inputs for Keys or Stops.
- Crystal Controlled Microcontroller
- DIP Switch Selection for MIDI Channels 1 to 16
- DIP Switch Selection for Keyboard Mode, starting Midi Note 36 or Stop Mode, starting Midi Note 0
- DIP Switch Selection for Stop Mode Midi Note Range, 0-63 or 64 to 128
- 24 Additional inputs for Pistons in the Keyboard Mode, or Stop in the Stop Mode.
- Up to 4 Analog Inputs for Three Swell Shoes and Crescendo
- No Matrix wiring conversion required. Use existing organ wiring.
- Ground Switching Keying, terminal inputs pull to Ground.
- Two 34 Conductor Ribbon cable or AMP 12 Terminal Punch Down Connectors
- MIDI IN and OUT Jacks
- MIDI Through
- Power Supply Input, 7 to 17 Volts DC.
- On board 5 Volt Regulator for the IC's.
- Low operating current , 10ma.
- Easy setup in Hauptwerk
- Cable Connectors Included
- Made in the U.S.A.
New MIPC-1A-HV
The MIPC-1A-HV offers the same functions of the MIPC-1A except the Terminal Inputs are POSITIVE keying voltage. The Terminal Input voltage can range from Plus 7 to Plus 17 volts D.C. NOTE: The MIPC-1A-HV is available only with the MOLEX KK-100 series connectors.
PIC-1 Pedal and Swell Shoe Midi Encoder
The PIC-1 will generate midi channel and note data pedal boards up to 32 notes. There are four analog inputs for up to four Swell Shoes. Wiring is direct from each pedal key contact to the matching input terminal on the PIC-1. There are no diodes and matrix wiring required. Midi Channel and Swell Shoe Enable are set by DIP Switch's, no configuration files required. For VPO installations that require only a pedal board midi encoder, the PIC-1 is the ideal choice.
Features.
Features.
- Up to 32 Pedal Inputs.
- Common Ground or Common Pisitive Keying.
- No Diode Matrix Wiring.
- Midi In and Midi Out Jacks
- Crystal Controlled Microcontroller
- Swell Shoe, Crescendo Inputs analog inputs.
- AMP Punch Down connector or 34 Pin Ribbon Cable Connector
- Negative Switching Inputs, Pull To Ground to send Midi Data.
- DIP Switch Midi Channel 1 to 16 selectable.
- NOTE, WHEN ORDERING, ADD A NOTE AS TO WHICH VERSION.
|
Click to set custom HTML
|
Reed Switch Pedal Contacts are now available to complete the pedal board conversion
See the "INTERFACE AND POWER SUPPLY PAGE FOR DETAILS.
See the "INTERFACE AND POWER SUPPLY PAGE FOR DETAILS.
LPC-1 Lighted Piston Controller
The LPC-1 will accept up to twelve lighted pistons and send midi data to the VPO software. Simply connect the piston switch to one of the 12 input terminals, the piston Lamp lead to the corresponding output terminal, set the Midi Channel and Midi Note range and connect the MIDI IN and OUT cables to a computer running Hauptwerk.
Features
* Up to 12 Pistons with Lamps.
* Simple DIP Switch Settings for MIDI Channel and MIDI Note Range.
* Crystal Controlled On Board Microcontroller.
* Midi IN and Midi OUT Jacks
* Optical Isolated MIDI Input.
* Operating Voltage Range from 8 to 18 VDC.
* No Configurations files to write or Computer programming.
Priced at $110.95
Features
* Up to 12 Pistons with Lamps.
* Simple DIP Switch Settings for MIDI Channel and MIDI Note Range.
* Crystal Controlled On Board Microcontroller.
* Midi IN and Midi OUT Jacks
* Optical Isolated MIDI Input.
* Operating Voltage Range from 8 to 18 VDC.
* No Configurations files to write or Computer programming.
Priced at $110.95
SSC-1 Swell Shoe Midi Controller.
The SSC-1 Swell Shoe Midi Controller is ideal for upgrades or adding a Swell Shoe to a midi keyboard. Up to four analog inputs are available as well as midi channels 1 to 16. Small size, 12 VDC operation, Midi IN and Midi Out jacks and NO Programming files to write, allow for simple and quick installation.
Features
$79.95 USD
Features
- Control up to Four Swell Shoes.
- Simple DIP Switch selection for Active Swell Shoes and Midi Channel selection
- Only 4" x 1.6"
- Crystal Controlled Microcontroller
- Midi IN and Midi OUT Jacks.
$79.95 USD
10 Ft Ribbon Cable with Connector
Ribbon Cable with mating connector for MIPC-1A, MIPC-1A-HV and PIC-1 MIDI Controllers. The 34 Conductor cables are TEN FEET. When ordering, TWO are required for the MIPC-1A Controllers and a SINGLE Cable is required for the PIC-1A Controller.
Cost, $15 each