64RB-1 Wire to Ribbon Cable Interface
The 64RB-1 is designed to be connected at the keyboard contacts an pedal contacts using short wire leads from the contacts to the WIRE Input side of the interface. The RIBBON CABEL connectors enable ribbon cable to be connected between the interface card the the Ribbon Cable connectors on the MIPC-1A and PIC-1 Input to MIDI cards, eliminating making 61 or 32 wire cables.
Included with the interface card and Five 12 terminal Molex connectors with terminals and One 4 terminal Molex, or Amp Punch Down Connectors.
The Molex Crimp terminals require a Molex Type Crimping Tool and the AMP Connecters require an AMP T Punch tool. See below for ordering the proper tool.
Included with the interface card and Five 12 terminal Molex connectors with terminals and One 4 terminal Molex, or Amp Punch Down Connectors.
The Molex Crimp terminals require a Molex Type Crimping Tool and the AMP Connecters require an AMP T Punch tool. See below for ordering the proper tool.
DCPS-12-3 Power Supply
Features, 110-220 AC plug in and well regulated 12 volt DC output that is rated at three amps. The 12 volt output includes short circuit protection, thermal shutdown and over current protection. Connection to the midi cards power inputs are made through a two wire adapter or DC Power Plug that is included.
$29.95 USD
Features, 110-220 AC plug in and well regulated 12 volt DC output that is rated at three amps. The 12 volt output includes short circuit protection, thermal shutdown and over current protection. Connection to the midi cards power inputs are made through a two wire adapter or DC Power Plug that is included.
$29.95 USD
DCPS-12-29 AC to 12 Volt 29 Amp DC Power Supply
Ideal for controlling stop actions and midi controller cards.
$59.95 USD
Ideal for controlling stop actions and midi controller cards.
$59.95 USD
Swell Shoe Slider Pot
The Swell Shoe Slide Pot assembly is available with a 5000 ohm pot for use with MIPC-1A and PIC-1 midi encoder systems. The Slider Pot includes mounting tabs on the printed circuit board for easy mounting to the shoe frame as shown. The kit includes a cable, linkage to connect to the shoe.
A universal mounting with the pot, cable and linkage is also available. Works with most brands of swell shoes.
A universal mounting with the pot, cable and linkage is also available. Works with most brands of swell shoes.
Reed Switch Pedal Contacts
The reed switch assembly is designed to be on a variety of pedal boards ranging for the flat style to AGO pedal boards. Unlike Glass enclosed reeds, these reed are enclosed in a rugged plastic enclosure and are mounted on a printed circuit board for easy mounting and wiring and includes a magnet. The reed switch's are priced at $3.75 each offer the best choice for updating or converting a pedal board.
Roland UM-One Midi to USB Converter
The Roland UM-One is a high quality Midi to USB interface that will offer long term reliable operation at a reasonable price. It is easy to install and comes complete with drivers for PC and MAC.
Priced at $53.95
Priced at $53.95
Go beyond the 50ft Midi cable Length with the
New Midi Ranger
Midi to RS-422 and CAT 5 Cable
Connect two Midi Rangers with up to 2000' of CAT5 cable.
Midi Ranger
The Midi Ranger is a Midi to RS-422 converter assembly that is designed for installations where the pipe chamber or midi devices are remotely located. Midi cables should not be any longer than fifty feet because of possible data lose. The Midi Ranger overcomes this by using the RS-422 technology that allows cable lengths of up to 2000 ft. Two units are required, one at the sending end and one at the receiving end. A single CAT-5 cable is required to provide full duplex, send and receive data transfer.
Buy Online using PayPal, $68.95 a pair.
The Midi Ranger is a Midi to RS-422 converter assembly that is designed for installations where the pipe chamber or midi devices are remotely located. Midi cables should not be any longer than fifty feet because of possible data lose. The Midi Ranger overcomes this by using the RS-422 technology that allows cable lengths of up to 2000 ft. Two units are required, one at the sending end and one at the receiving end. A single CAT-5 cable is required to provide full duplex, send and receive data transfer.
Buy Online using PayPal, $68.95 a pair.

NOTE: DUE TO PARTS SHORTAGE, THE CRIMPING TOOL IS OUT OF STOCK.
Hand Crimping tool for Molex KK-100 Series Terminals. This is a high quality Ratchet Type crimping tool that will give the best quality terminal crimp.
$39.95
Hand Crimping tool for Molex KK-100 Series Terminals. This is a high quality Ratchet Type crimping tool that will give the best quality terminal crimp.
$39.95
Instructions for using the Crimping Tool and crimp terminals.
AMP T Punch tool, $48.95